Cost guide
Pier and Beam Foundation Repair Cost (2026): Price by Repair Type
A pier and beam bill is a stack of separate jobs: adjusting the piers you have, adding or replacing supports, and repairing the wood they hold up. Price each one, and the wide national range starts to make sense.

Most 2026 cost guides put pier and beam foundation repair between about $800 and $25,000, and Angi puts the national average at $10,000. The useful number is the line item. Re-shimming is priced as a job total, about $800 to $5,500 across published sources. Most sources put a new or replacement pier at $800 to $6,000 each, and joist, beam and sill work is priced per piece or per foot.
Published 2026 benchmarks
$800–$25,000
Overall pier and beam repair range; most homeowners spend $6,000–$14,000
$10,000
National average (Modernize's average is $6,500)
$800–$3,500
Shimming existing piers (minor leveling), job total
$100–$120 per linear ft
Sill plate replacement
These are national figures from publishers and contractors with different project mixes. They are not a quote for your house. For a planning range based on your home’s size and symptoms, use the foundation repair cost calculator. For how each repair is actually carried out, see our guide to pier and beam foundation repair methods.
Pier and Beam Repair Prices by Scope
Pier and beam repairs fall into four pricing groups: adjusting existing supports (a job total), adding or replacing supports (per pier), repairing wood framing (per joist, per beam or per linear foot), and fixing the crawl-space moisture that caused the damage (a job total). Published sources price the same job differently, sometimes by two to five times, so the table shows each source rather than averaging them.
| Scope | Unit | Published ranges | What it usually covers |
|---|---|---|---|
| Re-shim / adjust existing piers | Job total | $800–$3,500 (Olshan); $1,000–$3,500 (Two Brothers); $1,000–$3,500 (Modernize); $1,200–$4,000 (Angi); $2,500–$5,500 (Black Beard) | Jacking the framing and adding or replacing shims on sound piers |
| Add a new pier or pad | Per pier | $800–$4,000 (Angi); $1,100–$3,000 for new pier addition or underpinning (Olshan) | A new support where spans sag or a support is missing |
| Replace a failed pier | Per pier | $1,100–$1,700 single (Olshan); $1,000–$1,600 steel pier swap (Two Brothers); $2,000–$6,000 (Angi); $2,500–$6,000 (Modernize) | Removing a cracked, tilted or sunken pier and setting a new one |
| Replace several piers | Job total | $6,600–$12,000, pier count not stated (Olshan) | Multiple pier replacement in one visit |
| Support post installation | Not stated | $1,300–$2,500 (Olshan) | Adding posts under sagging beams |
| Beam or girder replacement | Per beam | $400–$1,200 (Angi); wood from $1,500, steel up to $5,000 (HomeServe, 2024) | Swapping a rotted, cracked or undersized beam |
| Sister joists | Per joist | $100–$300+ (HomeAdvisor) | Bolting a new joist alongside a damaged one |
| Replace joists | Per joist | $350–$1,000 (Two Brothers; Modernize); $1,000–$2,000 (HomeAdvisor) | Removing and replacing a joist |
| Sill plate replacement | Per linear foot | $100–$120 (HomeAdvisor) | Replacing the rotted perimeter board the walls sit on |
| Crawl space moisture correction | Job total | $4,700–$8,200 drainage plus moisture correction (Olshan); $3,000–$20,000+ waterproofing (Modernize, Angi) | Drainage, vapor barrier, dehumidification |
| Whole-house releveling | Job total | $9,000–$23,000 (Olshan); $5,000–$12,000 (Modernize) | Adjusting and re-supporting the whole floor system |
| Underpinning with steel or helical piers | Per pier | $1,000–$3,000 (Angi, Modernize) | Deep piers under a perimeter beam, the high end of pier and beam work |
About these figures
Angi gives a per-square-foot figure ($6 to $8 on average, $0.50 to $17 at the extremes), but square footage doesn’t tell you how many supports or joists have failed, so don’t use it to check a quote. HomeServe’s figures date from 2024.
Access drives labor. Modernize notes that cramped crawl spaces cost more in labor and that limited crawl-space height increases labor time and cost, which is why access and clearance (covered below) move prices so much. Permits add $100 to $500 according to Modernize, or “a few hundred dollars” according to Angi.
Know roughly which jobs your house needs? Get a planning range before you call contractors.
Re-Shimming: What the Job Total Buys
A re-shim jacks the floor framing up off the piers and fills the gap with new shims. It is usually the cheapest pier and beam repair, and every published source prices it as one job total rather than per pier.
| Source | Job total | Range on a shared scale |
|---|---|---|
| OlshanDate: June 2026, 'minor leveling' | $800–$3,500 | |
| ModernizeDate: Sept 2026, 'reshimming' | $1,000–$3,500 | |
| Two BrothersDate: July 2026, 'leveling (shims)' | $1,000–$3,500 | |
| AngiDate: Sept 2026, table figure | $1,200–$4,000 | |
| Black Beard (DFW contractor)Date: June 2026, 'shimming/adjustments' | $2,500–$5,500 |
Angi’s article contradicts itself. Its table lists reshimming at $1,200 to $4,000, but elsewhere it says costs run “from under $1,000 for minor reshimming.” Black Beard’s higher range comes from one Dallas–Fort Worth contractor, and its scope may cover more than a basic shim pass.
Job totals, not per-pier prices
We couldn’t find any published per-pier or per-point price for re-shimming. Every source above prices the job as a whole, so we won’t invent a per-pier figure. When you get quotes, ask each contractor how many support points they plan to adjust. Two quotes at the same price can buy very different amounts of work. Also ask whether the price is a minimum charge for the visit, and what each extra point costs if they find more.
Steel or hardwood shims
Ask what the shims are made of. The Texas Section ASCE guidelines (section 7.5.1) say floor framing “may be adjusted by addition of shims atop pier caps” and that “hardwood or steel shims may be used to fill gaps.” A quote that doesn’t name a material is hard to compare with one that does. Ask to see what is going in, and photos afterward. Shimming on top of a cracked or tilted pier cap doesn’t solve the underlying problem.
How long a re-shim lasts
Modernize estimates that reshimming lasts 5 to 10 years, and new piers and beams “up to 25 years with maintenance.” Neither figure is a guarantee. Soil moisture swings, poor drainage and a wet crawl space shorten the interval. That’s why the warranty matters as much as the price: ask whether follow-up adjustments are included, for how long, and what voids them.
The 20-Year Cost of Repeated Re-Shimming
Repeated re-shims can add up to more than one round of new supports, but only if the house keeps needing them. The illustration below uses only published inputs to show how the totals compare.
Hypothetical illustration, not a prediction. Inputs: Olshan’s re-shim job total of $800 to $3,500, Olshan’s new pier addition at $1,100 to $3,000 per pier, and Modernize’s 5-to-10-year re-shim lifespan. All figures are in today’s dollars, with no inflation, and the house and pier count are invented.
- Re-shim only, 10-year interval: shims at year 0 and year 10 = 2 jobs. 2 × $800 = $1,600 to 2 × $3,500 = $7,000.
- Re-shim only, 5-year interval: shims at years 0, 5, 10 and 15 = 4 jobs. 4 × $800 = $3,200 to 4 × $3,500 = $14,000.
- Add four new piers once, then one re-shim: 4 × $1,100 = $4,400 to 4 × $3,000 = $12,000, plus a later re-shim at $800 to $3,500 = $5,200 to $15,500.
20-year totals in the illustration
$1,600–$7,000
Re-shim every 10 years (2 jobs)
Our calculation from Olshan job total × 2
$3,200–$14,000
Re-shim every 5 years (4 jobs)
Our calculation from Olshan job total × 4
$5,200–$15,500
Four new piers once, plus one later re-shim
Our calculation from Olshan per-pier × 4 + one job total
The ranges overlap, so neither path is always cheaper. What the arithmetic shows: if the house needs a re-shim every five years because the same piers keep sinking, the shim bills approach the cost of fixing the supports. In that case you are paying repeatedly for the symptom. If the piers are sound and a re-shim lasts a decade, shimming is the economical maintenance it’s meant to be. A contractor’s notes from each visit (which points moved, and by how much) are the evidence that tells you which case you’re in.
Adding or Replacing Piers
New or replacement piers cost about $1,000 to $3,000 each in most 2026 sources, and up to $6,000 each in Angi’s figures. Type, depth and soil explain most of the spread.
| Job and source | Per pier | Range on a shared scale |
|---|---|---|
| Steel pier swap (Two Brothers)Date: July 2026 | $1,000–$1,600 | |
| Single pier replacement (Olshan)Date: June 2026 | $1,100–$1,700 | |
| New pier addition or underpinning (Olshan)Date: June 2026 | $1,100–$3,000 | |
| Underpinning pier (Angi)Date: Sept 2026; segmented ~$1,000, steel ~$2,000, helical ~$3,000 | $1,000–$3,000 | |
| Adding piers (Angi)Date: Sept 2026; ~$2,000 average | $800–$4,000 | |
| Replacing piers (Angi)Date: Sept 2026; ~$3,000 average | $2,000–$6,000 |
Soil changes the count and the depth. Angi’s example: three to five steel piers cost $9,000 to $15,000 in loose or sandy soil, where piers have to go deeper, against $6,000 to $10,000 for the same work in dense clay with shallow bedrock. A short concrete pad set on the surface and a steel or helical pier driven to load-bearing soil are very different products, so a per-pier price only means something alongside the pier type and the depth. Per-pier pricing for steel and helical systems is covered in more depth in our foundation repair cost per pier guide.
Joist, Beam and Sill Repairs
Wood framing is priced per piece or per foot: roughly $100 to $300 to sister a joist, $400 to $1,200 or more per beam, and $100 to $120 per linear foot of sill plate. This is carpentry, not foundation work, so ask for it as separate line items.
| Job and source | Per joist | Range on a shared scale |
|---|---|---|
| Sistering, 8–10 joists together (Tygart Media)Date: Sept 2026 | $100–$180 | |
| Sistering (HomeAdvisor)Date: June 2026; 'or more' | $100–$300 | |
| Sistering, single joist installed (Tygart Media)Date: Sept 2026 | $175–$400 | |
| Joist replacement, crawl space (Two Brothers)Date: July 2026 | $350–$1,000 | |
| Full joist replacement (HomeAdvisor)Date: June 2026 | $1,000–$2,000 |
Sistering vs replacing joists
Sistering bolts a new joist alongside a damaged one and is usually far cheaper than removing the old one. HomeAdvisor puts sistering at $100 to $300 or more per joist against $1,000 to $2,000 for a full replacement. Tygart Media, which doesn’t name its data source, lists $175 to $400 for a single sistered joist and $100 to $180 each when eight to ten are done in one area. It adds that crawl spaces under 24 inches add 30 to 50 percent to labor per joist. Neither source publishes a per-linear-foot price for sistering, so a quote stated that way can’t be checked against published figures.
Sill plate rot, priced by the linear foot
The sill plate is the only framing member we found priced per linear foot. HomeAdvisor reports $100 to $120 per linear foot, or $2,500 to $6,000 for 25 to 50 feet, $10,000 to $18,000 for 100 to 150 feet, and $20,000 to $36,000 for 200 to 300 feet. It also notes that reaching the sill “often requires lifting the house,” at $15,000 to $21,000. Its page doesn’t say whether the per-foot rate includes that, so ask.
Beam and girder replacement
Angi prices beam replacement at $400 to $1,200 per beam, and says a typical home with 10 to 12 beams costs $4,000 to $12,000 for a whole-house replacement. Modernize lists the same $400 to $1,200 per beam. HomeServe’s 2024 figures start at $1,500 for a wood beam and go up to $5,000 for steel. We found no published per-linear-foot beam price.
Lumber grade affects the price
The Texas Section ASCE guidelines (section 7.5.2) say “treated lumber is recommended for general use in framing repairs.” Residential code also requires decay protection where wood joists are closer than 18 inches, or girders closer than 12 inches, to exposed ground in a crawl space (R317.1, as summarized by the City of Milpitas). In a low crawl space, a quote using untreated lumber may be cheaper because it doesn’t meet that requirement. Your local building department has the final word.
Crawl Space Conditions That Raise the Price
Low clearance, tight access and moisture damage raise pier and beam repair costs, because every hour under the house costs more when the crew can barely move.
Clearance and access
Residential code sets minimum crawl-space access openings: “not smaller than 18 inches by 24 inches” through the floor and “not less than 16 inches by 24 inches” through a perimeter wall (section R408.4, quoted from the 2025 California Residential Code; your jurisdiction’s adopted code applies). A house with only the minimum opening, or with no opening at all, means materials go in and old piers come out by hand. If a crew has to cut a new opening or dig out soil to make room to work, that should be a line item. Tygart Media’s 30 to 50 percent labor premium for joist work under 24 inches of clearance gives a sense of scale.
Moisture, rot and drainage
Moisture correction is often what makes a structural repair last. It can also be the biggest line on the bill.
| Job and source | Job total | Range on a shared scale |
|---|---|---|
| Dehumidifier (Angi)Date: Sept 2026 | $1,000–$4,000 | |
| Vapor barrier (HomeServe)Date: 2024; $2–$4 per sq ft | $1,200–$4,000 | |
| Sump pump (Angi)Date: Sept 2026 | $1,200–$2,500 | |
| Waterproofing (Modernize; Angi)Date: Sept 2026 | $3,000–$20,000 | |
| Drainage + moisture correction (Olshan)Date: June 2026 | $4,700–$8,200 | |
| Wood rot / moisture damage repair (Olshan)Date: June 2026 | $2,000–$25,000 | |
| French drain (Angi)Date: Sept 2026 | $8,000–$25,000 | |
| Encapsulation (Angi)Date: Sept 2026 | $12,000–$20,000 |
If moisture is the main problem rather than the supports, our planned crawl space repair cost guide covers encapsulation and drainage in more detail.
Safety first
A sagging or cracked beam, a floor that bounces or drops noticeably, or doors that suddenly won’t close all need prompt attention from a qualified professional. Don’t wait to collect a third quote. Contractors use temporary shoring to carry the house safely during the work, and you should never jack a floor yourself.
Three Pier and Beam Budgets, with the Arithmetic
These examples show how line items stack up into a total. The houses are invented, and each figure comes from a published range named alongside it. Mixing sources is a simplification, and your quotes will differ.
| Scenario | Line items (source) | Arithmetic | Planning range |
|---|---|---|---|
| A. Minor re-shim on sound piers | Re-shim job total (Olshan $800–$3,500; Black Beard high end $5,500) | One job | $800–$5,500 |
| B. Six new piers + two beams | New pier addition $1,100–$3,000 each (Olshan); beam replacement $400–$1,200 each (Angi); permit $100–$500 (Modernize) | 6 × $1,100 + 2 × $400 + $100 = $7,500; 6 × $3,000 + 2 × $1,200 + $500 = $20,900 | $7,500–$20,900 |
| C. Sill rot along one 40-ft wall + re-shim | Sill plate $100–$120 per ft (HomeAdvisor); re-shim $800–$3,500 (Olshan) | 40 × $100 + $800 = $4,800; 40 × $120 + $3,500 = $8,300 | $4,800–$8,300, before any house lifting |
Scenario C shows why it matters what a quote leaves out. HomeAdvisor says reaching the sill “often requires lifting the house,” at $15,000 to $21,000. If that applies, the budget more than triples, so find out whether a sill quote includes lifting, a section of wall supported on temporary shoring, or neither. None of these totals includes moisture correction, a plumbing leak test, or interior repairs to doors and drywall after the floor moves.
How to Read a Pier and Beam Quote
A good pier and beam quote lists each job separately, with a count, a unit and a material, so you can check every line against the published prices above. A single “level house” figure can’t be compared with anything.
| Line | What to look for | Why it matters |
|---|---|---|
| Support points adjusted | Number of points to be re-shimmed, and the charge for extras | No published per-pier shim price exists; the count is your only basis for comparison |
| Shim material | Steel or hardwood, named in writing | The materials the Texas Section ASCE guidelines name (7.5.1) |
| New or replacement piers | Count, type (concrete pad, block, drilled concrete, steel, helical), depth or target, and locations | Per-pier prices only compare when pier type and depth match |
| Framing repairs | Each joist, beam and sill section listed, lumber grade, treated or untreated, linear feet for sills | Carpentry is priced per piece or per foot; treated lumber is recommended (7.5.2) |
| Temporary shoring and access | Whether shoring, access openings or digging are included | Low clearance and tight access add labor time and cost (Modernize) |
| Moisture scope | Drainage, vapor barrier or dehumidifier included or excluded | Repairs in a wet crawl space don't last |
| Plumbing leak test | Included when jacking or lifting is planned | Texas Section ASCE guidelines say supply and drain lines should be tested when lifting is included (7.6) |
| Engineer and permits | Whether an engineer's plan or letter and the permit fee are included | Permits run about $100–$500 (Modernize) |
| Expected result | Target elevations or a before-and-after floor survey, not 'level' | Texas Section ASCE guidelines say a level foundation is unlikely after lifting (7.4.3.1) |
| Warranty | Term, whether follow-up re-shims are free, what voids it | Re-shims may last 5–10 years (Modernize) |
Don’t pay for a promise of “perfectly level.” The Texas Section ASCE guidelines state, in their section on slab underpinning (7.4.3.1), that “it is unlikely that elevation adjustments will result in a level foundation,” that adjustments “should be governed by field judgment to limit damage to the foundation and finishes,” and, more broadly, that “perfection is not attainable by remedial measures.” A contractor who promises otherwise is either overselling or planning to lift hard enough to crack finishes.
If quotes disagree about what is wrong, rather than about price, an independent opinion is worth more than a fourth bid. Our planned guide to hiring a structural engineer for foundation repair explains when that’s worth it. For leveling prices on other foundation types, see house leveling cost. For costs across every repair type, see the foundation repair cost guide.
Ready to compare itemized bids? Find contractors who work on pier and beam foundations near you.
Pier and beam repair cost questions
How much does it cost to reshim a pier and beam house?
Published 2026 guides price reshimming as a whole job, not per pier. Olshan lists $800 to $3,500, Two Brothers and Modernize $1,000 to $3,500, and Angi $1,200 to $4,000, while a Dallas-Fort Worth contractor, Black Beard, lists $2,500 to $5,500. Ask how many support points will be adjusted and whether the shims are steel or hardwood, the materials the Texas Section ASCE guidelines name.
What is the cheapest pier and beam repair?
Re-shimming existing piers is usually the lowest-cost fix, starting around $800 to $1,000 in published guides from Olshan and Modernize. It only makes sense when the piers and pads themselves are sound. If piers are cracked, tilted or still sinking, a shim job postpones the real repair, and you may end up paying for both.
How much does it cost to replace a pier under a house?
Olshan lists $1,100 to $1,700 for a single pier replacement and Two Brothers $1,000 to $1,600 per steel pier swap, while Angi puts replaced piers at $2,000 to $6,000 each. The spread reflects pier type, how deep the new support goes, soil, and how easy the crawl space is to work in. Ask each bidder to state the pier type and depth.
How much does it cost to sister floor joists?
HomeAdvisor's June 2026 guide puts sistering at $100 to $300 or more per joist, and full replacement at $1,000 to $2,000 per joist. Another 2026 guide quotes $175 to $400 for a single sistered joist, dropping to $100 to $180 each when eight to ten are done together, and adds 30 to 50 percent to labor in crawl spaces under 24 inches.
How much does sill plate replacement cost?
HomeAdvisor reports $100 to $120 per linear foot of sill plate replaced, which works out to $2,500 to $6,000 for 25 to 50 feet and $10,000 to $18,000 for 100 to 150 feet. It also notes that reaching the sill often means lifting the house, at $15,000 to $21,000, so ask whether a quote includes lifting or prices it separately.
How often does a pier and beam house need releveling?
Modernize estimates that a reshim lasts five to ten years, and that new piers and beams last up to 25 years with maintenance. The interval in your house depends on soil moisture swings, drainage and crawl-space conditions. Ask whether the contractor's warranty includes follow-up adjustments, for how long, and what voids it, before comparing prices.
Will releveling make my floors perfectly level?
Usually not. The Texas Section ASCE residential foundation guidelines, in their section on lifting slabs, say it is unlikely that elevation adjustments will result in a level foundation, and that lifting should be limited by field judgment to avoid damaging the structure and finishes. Expect noticeably better floors rather than perfect ones, and budget for door, trim and drywall touch-ups afterward.
Does homeowners insurance cover pier and beam repair?
Usually not for settling. GEICO's September 2026 guide says most homeowners policies exclude gradual settling or shifting of the foundation and cracks from wear and tear, but may cover damage from a sudden covered event such as a burst pipe. Earthquake and flood damage generally need separate coverage. Read your own policy's wording and ask your insurer before work starts.
Sources
- Angi — How Much Does Pier and Beam Foundation Repair Cost? (updated Sept 18, 2026)
- Modernize — Pier and Beam Foundation Repair Cost (updated Sept 23, 2026)
- Olshan Foundation Solutions — Foundation Repair Costs (modified June 3, 2026)
- Two Brothers Foundation Repair — Foundation Repair Cost research page (updated July 5, 2026)
- Black Beard Foundation Repair — How Much Does House Leveling Cost? (modified June 3, 2026)
- HomeAdvisor — Sill Plate Replacement Cost (updated June 19, 2026)
- HomeAdvisor — Floor Joist Repair Cost (updated June 20, 2026)
- HomeServe — Crawl Space Repair Cost (Oct 4, 2024)
- Tygart Media — Crawl Space Floor Joist Repair (modified Sept 7, 2026)
- Texas Section ASCE — Guidelines for the Evaluation and Repair of Residential Foundations, Version 3 (adopted April 1, 2022)
- 2025 California Residential Code, Section R408 Under-Floor Space, via GoCodebook (effective Jan 1, 2026)
- City of Milpitas, CA — Clearance and Protection Against Decay and Termites of Wood Floor Framing in Crawl Spaces (revised Mar 6, 2023)
- GEICO — Does Homeowners Insurance Cover Foundation Issues? (Sept 18, 2026)