Independent guide to foundation repair, costs and contractors. We’re a directory, not a contractor.

Repair methods

Pier and Beam Foundation Repair: Shimming, Supports, Framing and Crawl Space Fixes

A raised floor can sag because of soil, a pier, the wood framing or crawl-space moisture. The repair that lasts is the one aimed at the layer that actually failed.

Sources cited

Updated

Single-story house with a wraparound porch raised above the ground
Illustrative photo, not a listed contractor’s work. Credits

Pier and beam foundation repair means finding which layer failed (the soil under a pier, the pier itself, the wood framing, or crawl-space moisture) and fixing them in order: moisture and rot first, supports next, shims last. Shims level a floor; they do not add support. Common repairs are re-shimming, adding or replacing piers, sistering joists, and replacing sills or beams.

How the Load Gets to the Ground, and Where It Breaks

In a pier and beam house, every pound on the floor travels down through a chain of parts, and a sag can start at any link. If you know the chain, you can read a repair proposal and see which link it is fixing. (For how this foundation type compares overall, see pier and beam foundations explained.)

The pier and beam load path, top to bottom
LayerWhat it doesHow it typically fails
SubfloorSpans between joists and carries the finished floorSoft or spongy spots, usually from leaks near baths, kitchens or laundry
Floor joistsCarry the subfloor to the beamsBounce, sag, notching by past trades, rot or termite damage
Beams (girders)Carry the joists to the piersSag between piers when spans are long; rot where wood sits damp
ShimsFill the gap between beam and pier cap to set floor heightCrush, decay, slip out, or get stacked to hide a sinking pier
Interior piers and capsCarry beams down to the pad or footingTilt, crack, or sink with the pad beneath them
Pads or footingsSpread the load onto soilToo small for the load, or the soil under them shrinks, swells or softens
Perimeter beam, sill plate and pony wallsCarry the exterior walls; the sill is the wood resting on the concretePerimeter settlement and brick cracks; sill rot from splash-back or poor grading

Diagnose the Layer Before Choosing a Repair

Match the symptom to the layer it most likely points to, then ask for evidence of that layer before you agree to a fix. A shim job and a pier replacement can produce the same level floor on day one; only one of them addresses a sinking pad.

Pier and beam diagnostic matrix
What you noticeLikely layerTypical repairAsk the contractor for
Bouncy floor in one room, no slopeJoists (span, notching, damage)Sister or add joists, add a mid-span beamPhotos of joists, span and size, any cut or notched members
Soft subfloor near a tub, toilet or washerSubfloor and joists, from a leakFix the leak, replace subfloor and damaged joistsMoisture-meter readings, photos, plumbing check
Floor slopes toward the middle of the houseInterior piers or pads settlingReplace or add piers/pads, then re-shimAn elevation map, pier-by-pier condition notes
Gaps between beams and pier caps, loose shimsShims, or piers that have droppedRe-shim if piers are sound; reset piers if notWhich piers moved, shim material and stack height
Sag along one beam line between piersBeam span too long or beam damagedAdd supports or replace/reinforce the beamPier spacing, beam size, any rot or splits
Cracks in exterior brick, floor drops at outside wallsPerimeter beam settlementUnderpin the perimeter (pressed or steel piers)Exterior elevations and the pier layout drawing
Musty smell, damp soil, wood staining or fungusCrawl-space moistureDrainage, vapor retarder, ventilation or encapsulation, then wood repairPhotos of standing water, vent and grade conditions

To put a number on a slope, lay a long level on the floor and measure the gap at the low end, then divide by the length. The Texas Section ASCE Guidelines for the Evaluation and Repair of Residential Foundations (§5.6) note that foundation tilt can produce floor slopes and that “a tilt greater than 1 percent is usually noticeable.” Hypothetical example: across a 20-foot room, 1 percent is 240 inches × 0.01 = 2.4 inches of drop. That figure tells you whether a slope is likely to be noticed, not whether it is structurally acceptable; an engineer on site decides that. For symptoms beyond the floor, see uneven floors and foundation problems and the signs of foundation problems.

Safety first

A beam that is visibly sagging or split, a pier that has tipped over, or doors that suddenly won’t close are reasons to get a professional out promptly. Crawl spaces can also hold live wiring, sewage, pests and mold; don’t crawl under the house if it’s wet, tight or you’re unsure what’s down there.

Shimming and Re-Shimming

Shimming adjusts floor height by adding shims between the beam and the top of a sound pier; it is the right fix only when the pier, pad and framing are all in good shape. Texas Section ASCE describes it plainly: “Floor framing may be adjusted by addition of shims atop pier caps” (§7.5.1).

When shimming is the right fix

Shimming suits a floor that has drifted out of level because soil moved a little, old shims compressed, or a few piers settled slightly and then stopped. It is adjustable by design, which is its main strength: a crew can return and tweak heights without new concrete.

Steel vs hardwood shims

The same Texas Section ASCE section names both hardwood and steel shims. A Texas contractor’s guide (Maestro’s Foundation Repair, 2026) also mentions treated wood and composite shims. The choice matters most in damp crawl spaces.

Shim materials compared
Shim typeMoisture and decayFitting and adjustmentWhat to check
SteelDoes not rot; can corrode if left in standing waterComes in set thicknesses; stacks are adjusted by adding or removing platesThat plates sit flat and fully under the beam, and how they're held in place
HardwoodCan decay if the crawl space stays dampEasy to cut and taper on siteThat the wood is dry and sound, and that moisture is being controlled
Treated wood or compositeBuilt to resist decay; check the product's rating for ground contactCut or sized to fitProduct name and how the stack is secured

Whatever the material, ask the contractor to note what goes on each pier, how tall each stack is, and how it’s secured. If one pier needs far more shimming than its neighbors, ask why: that pier or its pad may be sinking.

Why re-shimming comes back on clay soils

There is no standard re-shimming interval, because it depends on how much the soil under your piers moves. Expansive clays “shrink when drying and swell when they become wetter,” and soils of this kind are concentrated in places including Texas and the lower Mississippi River Valley (USDA NRCS). Piers on that soil rise and fall with the seasons, so shims may need adjusting again. On a sound foundation, one contractor says properly done reshimming can last “many years or even decades” (Maestro’s); that is a contractor’s view, not a measured lifespan. More on the soil side: expansive clay soil and foundations.

When shimming is a band-aid

Shims don’t add support. They can’t fix a pad that is too small, a pier that keeps sinking, a beam spanning too far, or rotted wood. If re-shims are needed every year or two in the same spots, the fix belongs one layer down.

Adding or Replacing Piers and Pads

New or replacement supports are the fix when a pier has failed, a pad is too small, or a beam spans too far between supports. Texas Section ASCE says “additional supports can be installed when beam or floor framing spans are too great for the actual loading conditions,” and that added supports “should be compatible with the original foundation support system” (§7.5.3). It adds that “void spaces designed under foundation elements should be reestablished as necessary” (§7.5.4).

Perimeter beam vs interior piers

The perimeter and the interior often fail differently, so one proposal may use two methods. Interior piers carry beams on individual pads and are usually re-supported from inside the crawl space with new pads, precast blocks, poured cylinders or masonry piers (see concrete piers). The perimeter beam or stem wall carries the exterior walls continuously, much like a slab’s edge, so when it settles it is typically underpinned from outside with deep supports such as pressed concrete pilings or steel push piers. If a quote lists both, that’s often why. Ask which layer each line item addresses.

Ask too whether any jack post in the plan is temporary shoring during the work or the permanent support, and what it bears on.

Repairing Sills, Beams and Joists

Damaged wood should be replaced or reinforced, in treated lumber, after the moisture that damaged it is fixed. Texas Section ASCE puts it directly: “Structural members that are damaged or distressed should be replaced or reinforced,” and “treated lumber is recommended for general use in framing repairs” (§7.5.2).

Sistering vs replacement

Sistering fastens a new full-length member alongside a weak or cracked joist or beam so the two share the load. It works when the original member is still mostly sound. Replacement is for members that are rotted, eaten by termites or broken through. A steel flitch plate bolted between members is another way to stiffen a beam, and its size and bolting should come from an engineer.

Sill plate replacement

The sill plate is the wood resting on top of the perimeter concrete, and it carries the exterior walls. Replacing it means temporarily supporting the wall above, removing the bad section and installing new treated lumber. Rotted sills usually trace back to water at the perimeter, such as splash-back, high soil or a leak, so the proposal should name that cause too.

Termite and rot findings

If the crawl-space inspection turns up termite tubes or fungal decay, get the extent mapped before agreeing a price, because damage hidden inside members or behind finishes can enlarge the framing scope once work starts. Ask how added findings will be priced.

Crawl Space Moisture: Vents, Vapor Barriers and Encapsulation

Moisture control isn’t a structural repair, but it decides whether the wood repairs last. Texas Section ASCE lists “crawl space cross ventilation, under-floor drainage,” ground clearance for beams and joists, and treated lumber as under-floor moisture measures (§7.5.5). Deal with surface drainage and leaks first; a vapor barrier over a crawl space that floods won’t help. See water in a crawl space and plumbing leaks and foundations.

There are two code paths, both in IRC Section R408 (quoted here from the 2025 California Residential Code, which is IRC-based):

  • Vented (R408.2): net vent area of at least 1 square foot per 150 square feet of under-floor area, which may be reduced to 1/1,500 of the under-floor area where the ground is covered with an approved Class I vapor retarder. Knox County, Tennessee’s IRC crawlspace handout adds that one vent should be within 3 feet of each corner.
  • Unvented (R408.3): among other conditions, “exposed earth shall be covered with a continuous Class I vapor retarder.” This is the basis for encapsulation.

On the evidence for encapsulation, the U.S. Department of Energy’s Building America program reports that unvented, conditioned crawlspaces “use 15% to 18% less energy for heating and cooling while reducing humidity over 20%.” The deeper vented-vs-unvented choice is covered in crawl space foundations explained.

Access and Clearance: What the Code and Your Crawl Space Allow

How much room there is under the house affects what can be done from below and how hard the job is. Under IRC R408.4, “access openings through the floor shall be not smaller than 18 inches by 24 inches,” and “openings through a perimeter wall shall be not less than 16 inches by 24 inches” (2025 CRC via GoCodeBook; also in Knox County’s handout). R408.5 adds that “the under-floor grade shall be cleaned of all vegetation and organic material.”

Clearance also matters for decay. IRC R317.1 calls for protection against decay (treated or naturally durable wood) where “wood joists or the bottom of a wood structural floor without joists are closer than 18 inches” or “wood girders are closer than 12 inches to the exposed ground in crawl spaces,” as quoted from the 2022 California Residential Code in a City of Milpitas building policy. In practice, new framing in a low crawl space should be treated lumber.

Where clearance is very tight, crews may need to dig out working room, enter through a cut in the floor, or limit what they can reach. Ask how the crew will get to each repair point and whether that is in the price. Your city’s adopted code edition governs, so confirm these numbers locally.

The Right Order of Operations

Fix the cause before you level the result. This sequence follows the repair categories in Texas Section ASCE §7.5–7.6, arranged so later steps don’t undo earlier ones:

  1. Stop the water. Correct drainage, grading and plumbing leaks that are wetting the crawl space or soaking the soil under piers.
  2. Map the damage. Record rot, termite damage and failed piers, plus a set of floor elevations to compare against later.
  3. Repair the wood. Replace or sister damaged joists, beams and sills with treated lumber.
  4. Fix the supports. Replace failed piers or pads, add supports where spans are too long, and underpin the perimeter if it has settled.
  5. Shim and level last. Set final heights on sound supports, gradually, so finishes and plumbing aren’t stressed. Lifting limits are covered in house leveling.
  6. Test the plumbing. Texas Section ASCE says supply and sanitary drain lines “should be tested for leaks if jacking or lifting is included in the remedial measures” (§7.6).
  7. Control moisture for the long term. Vapor retarder, ventilation or encapsulation, and re-establish void space where the design calls for it.
  8. Re-measure. Take final elevations at the same points as step 2 and keep the report with your house records.

Permits and Engineer Letters for Pier and Beam Work

Many cities treat shimming and floor-system work as permitted foundation repair, not handyman work. The City of McKinney, Texas, for example, defines foundation repair as “any leveling, replacement of piers, footings, shimming, or replacement of any part of the floor system,” applies it to “both slab-on-grade and pier & beam foundations alike,” and requires an engineer’s letter and drawings. Rules vary by city, so ask who pulls the permit and whether an engineer designs or inspects the work. An independent structural engineer is also useful when two quotes disagree about which layer failed.

What Drives the Price

Pier and beam repair cost depends on how many layers need work, not just how many piers. As a rough orientation, Angi puts the national average at $10,000, with most homeowners spending $6,000 to $14,000 (Angi, updated Sept. 18, 2026). That covers everything from a re-shim to major framing work. The main drivers:

  • Whether the job is a re-shim on sound supports or new piers and pads
  • How much rotted or termite-damaged wood has to be replaced
  • Perimeter underpinning, which uses a different and deeper method than interior supports
  • Crawl-space clearance and access, plus any moisture or encapsulation work

Line-item prices and how they compare are in the pier and beam repair cost guide; slab homes are covered in slab foundation repair.

Get a planning range for your own house before you collect quotes.

Choosing a Crew for Raised-Floor Work

A pier and beam job often needs carpentry, concrete and moisture work in the same crawl space, so look for a contractor who handles framing in-house or names the subcontractor, and whose proposal says which layer each item fixes. Ask for crawl-space photos, a pier layout, before-and-after elevations and the warranty terms for each part of the work, since understructure and pier warranties can differ.

Compare vetted contractors who do pier and beam, framing and crawl-space work.

Pier and beam repair questions

Can a pier and beam foundation be repaired?

Yes, and the crawl space usually gives crews direct access to the parts that need work. Texas Section ASCE guidelines list the main options: shimming the floor framing atop existing supports, repairing or strengthening framing, replacing or adding supports, and re-establishing void space. Fix moisture and rot first, because shimming wet or decayed framing only hides the problem for a while.

How often does a pier and beam house need re-shimming?

There is no standard interval. It depends on how much the soil under the piers moves as it wets and dries. On expansive clay, seasonal swings can shift piers enough that shims need adjusting again; one Texas contractor's guide says reshimming done properly on a sound foundation can last many years or even decades. If you need re-shims every year or two, ask whether the piers or drainage are the real problem.

Are steel shims or wood shims better?

Texas Section ASCE guidance names both hardwood and steel shims placed atop pier caps. Steel does not rot, which matters in a damp crawl space. Hardwood is easy to cut to fit but can decay if moisture is not controlled. Whichever is used, ask the contractor what material goes on each pier, how the stack is secured, and why any single pier needs much more shimming than its neighbors.

How do you reinforce a pier and beam foundation?

The usual options are adding piers or pads where beam spans are too long for the load, sistering or replacing weak joists, replacing rotted beams or sill plates, and underpinning a settling perimeter beam with pressed or steel piers. Texas Section ASCE guidance recommends treated lumber for framing repairs. Pair any structural work with crawl-space moisture control so the new wood stays dry.

Is crawl space encapsulation part of foundation repair?

It is moisture control, not structural repair, but it protects the wood that carries the house. The IRC allows an unvented crawl space when exposed earth is covered with a continuous Class I vapor retarder, under section R408.3. Department of Energy Building America research found unvented, conditioned crawlspaces used 15 to 18 percent less heating and cooling energy and reduced humidity by over 20 percent.

How much crawl space access is required?

Under IRC section R408.4, an access opening through the floor must be at least 18 by 24 inches, and an opening through a perimeter wall at least 16 by 24 inches. Your city may have adopted a different code edition, so confirm locally. Very low clearance under beams can also limit what crews can do from below and may mean opening the floor or digging out working room.

Does pier and beam repair need a permit?

It depends on the city. McKinney, Texas, for example, defines foundation repair as including any leveling, replacement of piers, footings, shimming, or replacement of any part of the floor system, applies that to pier and beam homes as well as slabs, and requires an engineer's letter and drawings. Ask your contractor who pulls the permit and whether an engineer will sign off.

Sources