Cost guide
Slab Foundation Repair Cost: Per-Pier Prices, Pier Counts and Slab Extras
A slab repair bill is mostly pier count times pier price, plus a set of slab-only extras that base quotes often leave out. Here are the published numbers and the arithmetic.

Most slab foundation repairs cost about $3,500 to $10,000 (HD Foundations; Perma Pier, 2026), inside a published envelope of $350 to $20,000 (Bob Vila). Pier count times pier price drives the bill: a 4–6-pier corner on steel push piers works out to about $3,960–$8,100 before plumbing tests, engineering and floor repairs.
What Slab Foundation Repair Usually Costs
A typical concrete slab foundation repair costs a few thousand dollars for a settled corner and $15,000 to $30,000 or more when most of the house needs underpinning. The spread is wide because “slab repair” covers everything from sealing a crack to piering the whole perimeter.
The broad envelope of $350 to $20,000 appears on Bob Vila (May 2024) and LendEDU (April 2026, which says its costs were sourced via Angi). Contractor figures are narrower: HD Foundations, a North Texas company, says slab repair “ranges between $3,500-6,500” and that severely cracked or sloping slabs “can exceed $10,000.”
| Scope | Typical piers | Published range | Source |
|---|---|---|---|
| Crack sealing only, no movement | None | Low end of the $350–$20,000 envelope | Bob Vila; see the crack repair cost guide |
| Typical slab stabilization | 5–15 | $3,500–$6,500 average; $3,000–$10,000+ | HD Foundations; Perma Pier (pier count: Olshan) |
| Average Texas repair | 4–8 | $5,000–$10,000 | AskDoss |
| Larger Texas repair | 10+ | $10,000–$15,000 | AskDoss |
| Interior pier jobs | 6–20 | $6,000–$60,000+ | Perma Pier |
| Full perimeter or severe failure | 15–25 | $15,000–$30,000+ | AskDoss; Olshan |
These are published ranges, not quotes. AskDoss is a mortgage-site editorial guide, so treat its tiers as a cross-check rather than a benchmark. For the same job on a different foundation type, see the foundation repair cost hub.
Cost Per Pier Under a Slab, by Pier Type
Slab piers run from about $400 to $4,400 each in 2026 published prices, with concrete piers at the low end and helical piers at the top. Prices differ by pier type and by who publishes them, so compare a quote against the same pier type.
| Pier type | Per pier | Range on a shared scale |
|---|---|---|
| Pressed concrete piling, TexasSource: AskDoss, Mar 2026 | $400–$600 | |
| Drilled concrete pierSource: Olshan, Jun 2026 | $765–$1,100 | |
| Steel push pierSource: Olshan, Jun 2026 | $990–$1,350 | |
| Concrete pierSource: Perma Pier, Apr 2026 | $1,000–$3,000 | |
| Interior slab pier (any type)Source: Perma Pier, Aug 2024 | $1,000–$3,000 | |
| Steel pressed pilingSource: Ram Jack, Aug 2026 | $1,500–$3,000 | |
| Steel pierSource: Perma Pier, Apr 2026 | $1,500–$4,000 | |
| Helical pierSource: Ram Jack, Aug 2026 | $2,000–$4,000 | |
| Helical pierSource: Olshan, Jun 2026 | $3,500–$4,400 |
Sources: Olshan, Ram Jack, Perma Pier and its interior repair page, and AskDoss. These figures match the ones used in our house leveling cost guide.
A Texas engineering firm’s estimating worksheet gives a useful ranking. A-1 Engineering prices pile cost as building square footage × 0.025 × a rate of $350 for concrete pressed piles, $550 for steel pressed piles, $700 for helical steel piles and $950 for cast-in-place concrete piers, and notes that its numbers vary across the state and by project. Its rates sit below most contractor-published prices, so treat them as relative, not as a local price.
Which pier fits your slab is an engineering question, not a price one. Push piers need the house’s weight to drive them, which is why interior slab piers are often helicals; the slab foundation repair methods guide explains each type. A deeper cost per pier guide, plus helical pier and push pier cost pages, are planned.
How many piers a slab repair needs, and what that totals
A slab repair usually needs 4 to 6 piers for a corner, 12 to 20 or more for a full side, and 15 to 25 for a full perimeter. Olshan says “most slab jobs require 5–15 piers,” 4–6 for a small corner and 12–20+ for widespread settlement along a full side; AskDoss gives 15–25 for a full perimeter. No source we checked publishes a standard pier spacing, so the count on your quote should come from an engineer’s layout.
Multiply the count by the per-pier price to see the range. The table uses Olshan’s per-pier figures throughout so the rows are comparable.
| Extent | Piers | Drilled concrete ($765–$1,100) | Steel push ($990–$1,350) | Helical ($3,500–$4,400) |
|---|---|---|---|---|
| One corner | 4–6 | 4 × $765 = $3,060 to 6 × $1,100 = $6,600 | 4 × $990 = $3,960 to 6 × $1,350 = $8,100 | 4 × $3,500 = $14,000 to 6 × $4,400 = $26,400 |
| Typical slab job | 5–15 | $3,825 to $16,500 | $4,950 to $20,250 | $17,500 to $66,000 |
| One full side | 12–20 | $9,180 to $22,000 | $11,880 to $27,000 | $42,000 to $88,000 |
| Full perimeter | 15–25 | $11,475 to $27,500 | $14,850 to $33,750 | $52,500 to $110,000 |
About these figures
Same corner, different pier
$3,060–$6,600
4–6 drilled concrete piers
Our calculation from Olshan, 4–6 × $765–$1,100
$3,960–$8,100
4–6 steel push piers
Our calculation from Olshan, 4–6 × $990–$1,350
$14,000–$26,400
4–6 helical piers
Our calculation from Olshan, 4–6 × $3,500–$4,400
To plug in your own pier count and region, use the foundation repair cost calculator.
Slabjacking and Foam: House Slab vs Driveway-Type Slab
Lifting a house slab with grout or polyurethane foam costs about $4,500 to $11,500 per project, far more than leveling a driveway or patio. The method has the same name in both cases, but published flatwork prices don’t apply to a house.
| Job | Published price | Source |
|---|---|---|
| Mudjacking a house slab | $5,000–$10,800 per project | Olshan, Jun 2026 |
| Polyurethane foam lifting, house slab | $4,500–$11,500 per project | Olshan, Jun 2026 |
| Polyurethane injection, residential | $1,000–$3,000 | Ram Jack, Aug 2026 |
| Mudjacking or slabjacking | $4–$6 per sq ft | HD Foundations |
| Mudjacking, per section | $500–$1,500 per section | Perma Pier, Apr 2026 |
| Slabjacking (unspecified slab) | $500–$1,300 | HomeAdvisor, Jun 2026 |
| Flatwork mudjacking (driveways, patios) | $3–$8 per sq ft | Inch Calculator, Aug 2023 |
| Flatwork foam lifting | About $20–$25 per sq ft; a 100 sq ft job about $2,000–$2,500 | Inch Calculator |
Why the gap: a house slab carries the walls and roof, the lift has to be controlled across a larger area, and the plumbing has to be tested afterward. Olshan’s own page also shows a lower $1,900–$3,800 mudjacking figure in its quick summary, so ask any bidder what area and lift their number covers.
Foam and grout lift from just under the slab. Texas Section ASCE’s repair guidelines describe mudjacking as adjusting “elevations of a foundation hydraulically with continuous uniform support,” but neither method changes what the deeper soil does. On clay that keeps shrinking and swelling, a foam quote that beats a pier quote may be buying a shorter-lived repair. When each method fits is covered in polyjacking vs mudjacking.
Slab-Only Extras: Plumbing Tests, Access and Finishes
Expect a further few thousand dollars on top of the pier price for slab-only work: plumbing tests, getting to interior piers, and repairing floors and walls afterward. These lines are often outside the foundation contractor’s base number.
| Item | Published cost | Source | Ask the bidder |
|---|---|---|---|
| Plumbing static or hydrostatic test | $800 (engineer's worksheet); from about $1,650 (Houston plumber) | A-1 Engineering; Nick's Plumbing | Tested before and after the lift? Who pays? |
| Leak isolation testing | $295 per hour | Nick's Plumbing | Is isolation included if the test fails? |
| Slab leak detection | $150–$600 | This Old House | Needed only if a leak is suspected |
| Under-slab plumbing repair | $500–$4,000 (incl. tunneling or opening the slab); $3,000 with permit | This Old House (HomeAdvisor data); A-1 Engineering | Who repairs leaks the post-lift test finds? |
| Tunneling under the slab | $3,000–$12,000+ per project | Modernize | Tunnel length, backfill and compaction method |
| Interior break-out | Building sq ft × 0.0125 × $75 (worksheet formula; $1,875 for 2,000 sq ft) | A-1 Engineering | How many openings, and who patches the concrete? |
| Concrete restoration after slab is opened | $2,000–$7,500 | This Old House | Is the patch included? |
| Flooring or tile repair | $4,000 (worksheet line); $500–$2,500+ | A-1 Engineering; Modernize | Is flooring excluded in writing? |
| Sheetrock crack repair | $3,500 (worksheet line) | A-1 Engineering | Any cosmetic repair included? |
| Structural engineer report | $340–$780; $499–$780; Houston $400–$1,000 | HomeAdvisor; Olshan; Angi Houston | Independent engineer or the contractor's? |
| Soil report | $500–$3,000 | HD Foundations; Bob Vila | Needed for this job? |
| Permit | $300 (Texas example); $300–$600 (Austin) | A-1 Engineering; Angi Austin | Who pulls it? |
| Post-repair floor elevation survey | No published price found | Expected by Texas ASCE Sec. 7.7 | Is a final survey included? |
| Landscaping after repairs | $1,000 (worksheet line) | A-1 Engineering | Who restores beds and irrigation? |
| Drainage correction or regrading | $2,800–$8,000 | Olshan | Is the water source being fixed too? |
The plumbing test isn’t optional when the slab is lifted. The Texas Section ASCE guidelines (Sec. 7.6) say “water supply and sanitary drain lines should be tested for leaks if jacking or lifting is included in the remedial measures.” Nick’s Plumbing calls testing “especially important before foundation work, tunneling, or slab access,” and Perma Pier notes that “plumbing problems in the first 3 months or so are not uncommon” after a repair. If a leak caused the movement, see plumbing leaks and foundation damage; whether insurance helps is covered in does insurance cover foundation repair.
Tunneling vs breakout: why interior piers cost more
Interior piers cost more than perimeter piers because the crew has to reach a beam under the house, either by tunneling in from outside or by cutting through the floor. Perma Pier lists interior piers at $1,000–$3,000 each, with 6–20 typical, for $6,000–$60,000+ per job.
Tunneling keeps the floors intact but is priced by the project: Modernize puts it at $3,000–$12,000+, and none of the sources we checked publishes a per-foot rate. A-1’s worksheet budgets interior break-out by building size (square footage × 0.0125 × $75, or $1,875 for a 2,000 sq ft house), below Modernize’s tunneling range, but the floor over each hole has to be patched and refinished, which is where the $500–$4,000 flooring lines come in. No source we checked publishes a price per opening. How each access method is done, and its risks, is in the slab repair methods guide.
Worked example: a settled corner with two interior piers (hypothetical)
This illustrative budget assumes an engineer calls for 5 exterior steel push piers and 2 interior piers by breakout, on a slab with tile floors. Every line is a published figure; the job itself is invented. No source publishes a per-opening break-out price, so the budget assumes the interior pier price covers the openings; ask each bidder whether it does.
| Line item | Arithmetic | Low | High | Source |
|---|---|---|---|---|
| Exterior steel push piers | 5 × $990 to 5 × $1,350 | $4,950 | $6,750 | Olshan, Jun 2026 |
| Interior piers | 2 × $1,000 to 2 × $3,000 | $2,000 | $6,000 | Perma Pier, Aug 2024 |
| Structural engineer report | One report | $499 | $780 | Olshan, Jun 2026 |
| Plumbing test | One test | $800 | $1,650 | A-1 Engineering; Nick's Plumbing |
| Permit | Texas example | $300 | $300 | A-1 Engineering |
| Flooring repair over break-outs | One range | $500 | $2,500 | Modernize |
| Total | Sum of the rows | $9,049 | $17,980 | Our calculation |
Dropping the two interior piers and the flooring repair would take $2,500–$8,500 off this budget ($2,000 + $500 to $6,000 + $2,500). That’s the case for asking whether interior piers are really needed, and what the engineer’s elevation survey shows, before you accept them.
Worked example: whole-house underpinning by an engineer’s formula (hypothetical)
A-1 Engineering’s worksheet estimates a whole-house job from floor area: pile cost = building square footage × 0.025 × the pile rate, and interior break-out = building square footage × 0.0125 × $75. For a 2,000 sq ft slab, break-out comes to 2,000 × 0.0125 × $75 = $1,875. Adding that break-out line and the worksheet’s fixed lines (permit $300, engineering inspection $600 or $900, lift $2,000, plumbing test $800, plumbing repair $3,000, landscaping $1,000, sheetrock $3,500, flooring $4,000) gives:
| Pile system | Pile cost | Inspection | Other lines | Total |
|---|---|---|---|---|
| Pressed concrete | 2,000 × 0.025 × $350 = $17,500 | $600 | $16,475 | $34,575 |
| Steel pressed | 2,000 × 0.025 × $550 = $27,500 | $600 | $16,475 | $44,575 |
| Helical steel | 2,000 × 0.025 × $700 = $35,000 | $900 | $16,475 | $52,375 |
| Cast-in-place concrete | 2,000 × 0.025 × $950 = $47,500 | $900 | $16,475 | $64,875 |
About these figures
Post-Tensioned Slabs: What Changes in the Quote
A post-tensioned (PT) slab can be repaired with the same piers, but any cutting, coring or interior work has to avoid the steel tendons, and no cost source we found publishes a separate PT repair price. Treat any PT surcharge on a quote as something to ask the bidder to explain, not something to compare against a benchmark.
What changes in the work, and so in the scope you’re paying for:
- Confirm the slab type first. Builders often stamp PT slabs with a warning against cutting or drilling, according to NewHomeSource, which says PT slabs are used “particularly in the Gulf Coast region and tropical areas with largely expansive soils” and that when the steel rips through the slab, it can “become nearly impossible to repair.”
- Locate tendons before openings. In JLC, structural engineer Brian Allred writes that it’s important to avoid cutting any tendon “since that will weaken the foundation,” that “cutting through one is also potentially hazardous,” and that tendon locations “can be pinpointed with a high-strength metal detector or digital scanner.” Openings “should be located several feet away” from anchorages. Ask whether scanning is in the price.
- Fewer break-outs, more engineering. Those limits can push a plan toward tunneling or exterior work and toward closer engineer involvement, both of which affect cost.
- Tendon re-stressing is sequenced last. The Texas ASCE guidelines (Sec. 7.4.3.4) say stressing relaxed or inadequately stressed tendons “should be performed after elevation adjustments and epoxy crack injecting.”
Don't drill a PT slab
Why Texas and Gulf Coast Slab Repairs Cost What They Do
Slab repair is a bigger budget line in Texas and along the Gulf Coast mainly because expansive clay keeps moving, so more jobs need piers and drainage work rather than a one-time patch. The Texas inspector bulletin TB 10-01, summarizing IRC R403.1.8.1, treats soil as expansive when it has a plasticity index of 15 or more plus two fine-particle criteria, or an expansion index above 20, and says expansive soils “are a very common cause” of foundation problems.
Published regional figures sit close to the general slab ranges above. Angi puts slab repair in Austin at $3,000–$8,500, close to HD Foundations’ North Texas average. What clay adds is the drainage line: Olshan lists drainage correction at $2,800–$8,000, and the residential code’s grading rule, as quoted by InterNACHI, is that “the grade shall fall not fewer than 6 inches (152mm) within the first 10 feet” (IRC R401.3). A pier job that leaves water pooling at the slab edge is paying to fight the same cause twice.
The soil mechanics are in expansive clay soil and foundations. State and city pages, foundation repair cost in Texas and in Houston, are planned.
What Drives Slab Repair Cost
Pier count is the biggest driver, then pier type, then whether the work has to go inside the house. The rest adds up from testing, engineering and finishes.
- How many piers. Olshan’s 5–15 range alone triples the pier cost of a job.
- Pier type. Olshan’s helical piers cost more than three times its steel push piers ($3,500–$4,400 against $990–$1,350).
- Interior access. Interior piers add break-outs or tunneling plus floor restoration.
- The cause. A plumbing leak or poor drainage means a plumbing repair or regrading line on top of the piers.
- Slab type. PT slabs need tendon locating and tighter limits on openings.
- Engineering, soil testing and permits. Several hundred to a few thousand dollars combined, per the extras table above.
- How much lift is attempted. The Texas ASCE guidelines say “it is unlikely that elevation adjustments will result in a level foundation,” so don’t pay a premium for a promise of dead level. More lift means more stress on drywall, tile and pipes.
How to Compare Slab Repair Quotes
Compare slab repair quotes line by line on the same pier layout, because two totals can describe very different jobs. Ideally, get an independent engineer’s plan first and ask every company to bid it; the Texas ASCE guidelines say repair plans should specify underpinning “locations,” “sizes, depths, material types.”
Ask each bidder to put these in writing:
- Pier type, pier count and price per pier, plus a plan showing where each pier goes, exterior and interior.
- Installation criteria: the depth or pressure each pier must reach before it’s accepted, and how extra piers are priced if needed.
- Interior access method: tunneling or breakout, and who patches concrete and restores flooring.
- Lift target in writing, and what happens if the crew stops short.
- Plumbing testing before and after, who hires the plumber, and who pays for leaks found after the lift.
- Engineering and permit: included or separate.
- A final floor elevation survey, which the Texas ASCE guidelines expect after the work (Sec. 7.7).
- PT slabs: how tendons will be located before any opening.
- Warranty: what it covers, and whether it transfers to a buyer. See foundation repair warranties.
- Exclusions: drywall, tile, landscaping and drainage.
If bids disagree on the cause or the method, not just the price, an independent structural engineer is worth the $340–$780 HomeAdvisor lists for a report. A guide to reading a foundation repair estimate is planned.
Ready to price it? Ask vetted slab repair contractors for an itemized quote with pier count and plumbing test in writing.
Don't wait for quotes
Slab foundation repair cost questions
How much does slab foundation repair cost?
Most slab repairs land around $3,500 to $10,000. North Texas contractor HD Foundations puts the average at $3,500 to $6,500, and Perma Pier lists $3,000 to $10,000 or more for slab stabilization. Bob Vila's broader envelope runs from $350 for minor work to $20,000. Severe failures needing full underpinning reach $15,000 to $30,000 or more, according to Olshan's June 2026 guide.
How many piers does a slab foundation need?
Olshan says most slab jobs need 5 to 15 piers: 4 to 6 for a small corner and 12 to 20 or more when a full side has settled. A Texas cost guide from AskDoss gives 15 to 25 for a full perimeter. The exact number should come from an engineer's plan; Texas Section ASCE guidelines say repair plans should specify pier locations, sizes, depths and materials.
What does a slab pier cost by type?
Olshan's June 2026 table lists drilled concrete piers at $765 to $1,100, steel push piers at $990 to $1,350 and helical piers at $3,500 to $4,400 each. Ram Jack lists steel pressed pilings at $1,500 to $3,000 and helicals at $2,000 to $4,000. A Texas engineering firm's estimating worksheet uses a $350 rate for pressed concrete piles in its pile-cost formula, the lowest of its four pile rates.
Do I need a plumbing test before slab repair?
Yes, if the slab will be lifted. Texas Section ASCE guidelines say water supply and sanitary drain lines should be tested for leaks if jacking or lifting is included in the repair. A hidden drain leak can also be what caused the movement. A Texas engineer's worksheet lists an $800 static test, and a Houston plumber advertises hydrostatic tests starting around $1,650.
Is polyurethane foam cheaper than piers for a slab?
Not always, and it solves a different problem. Foam and mudjacking fill voids and lift a slab from just underneath without reaching deeper soil. Olshan lists foam lifting under a house at $4,500 to $11,500 per project, which overlaps a small steel pier job. On expansive clay that keeps moving, an engineer may recommend piers even when the foam quote is lower.
Does a post-tensioned slab cost more to repair?
Possibly, but no cost source we found publishes a separate price for post-tensioned slab repair. What changes is the work: tendons must be located before any cutting, openings kept away from anchorages, and any tendon re-stressing done after lifting and crack injection, per Texas Section ASCE guidelines. Ask each bidder how they will locate tendons and whether that is priced in.
Will my slab be perfectly level after repair?
Usually not, and you should not pay as if it will be. Texas Section ASCE guidelines state that it is unlikely elevation adjustments will result in a level foundation, because lifting is limited to avoid damaging the structure and finishes. Ask for target elevations in writing and for a floor elevation survey after the work, which the same guidelines expect.
Sources
- HD Foundations — Slab Foundation Repair Cost (published Aug 17, 2023, modified June 2, 2026)
- Perma Pier — Foundation Repair Cost (April 14, 2026)
- Perma Pier — Interior Foundation Repair (Aug 1, 2024)
- Bob Vila — How Much Does Foundation Repair Cost? (updated May 29, 2024)
- LendEDU — Foundation Repair Cost (updated April 1, 2026; costs sourced via Angi)
- Olshan Foundation Repair — Foundation Repair Costs (modified June 3, 2026)
- Ram Jack — Cost of Foundation Repair (Aug 27, 2026)
- A-1 Engineering — Estimating the Cost of Foundation Repair (modified July 23, 2026)
- AskDoss — How Much Does Foundation Repair Cost in Texas in 2026? (updated March 4, 2026)
- HomeAdvisor — Foundation Repair Cost (updated June 20, 2026)
- Angi — Foundation Repair Cost in Austin, TX (Oct 10, 2025)
- Angi — Structural Engineer Cost in Houston, TX (updated July 8, 2026)
- Inch Calculator — Concrete Slab Leveling Cost Guide (Aug 6, 2023)
- Nick's Plumbing — Hydrostatic Leak Detection, Houston (pricing updated June 5, 2026)
- This Old House — Slab Leak Repair Cost (updated April 7, 2026)
- Modernize — Slab Leak Repair Cost (updated Aug 12, 2026)
- Texas Section ASCE — Guidelines for the Evaluation and Repair of Residential Foundations, Version 3 (adopted April 1, 2022)
- JLC — Adding a Point Load to a Post-Tensioned Foundation, Brian Allred, S.E. (March 1, 2012)
- NewHomeSource — Post-Tension Foundations in New Home Construction (Oct 21, 2024)
- Texas Department of Licensing and Regulation — Inspector Technical Bulletin TB 10-01 (rev. Oct 16, 2018)
- InterNACHI — Foundation Grade, quoting IRC R401.3 (undated)